Among the best security cameras available today, Blink security cameras are without a doubt the best. Blink Camera Not Detecting Motion is a complaint made by many users. It is important to find the main cause of this problem before we can fix it.
There could be a variety of reasons behind this Blink Camera Not Detecting Motion errors. In case of any issue with the Blink camera, you will see the message “camera busy” or “thumbnail failed”.
Throughout this guide, we will give you all the steps you need to take to repair your Blink camera.
We have technicians with many years of experience that can help you as well. Within a short timeframe, they can resolve any issue.
Why Isn’t My Blink Camera Picking Up Motion?
Following are some main reasons why your Blink Camera Not Detecting Motion :
- It is disabled to blink the camera
- Your system is suffering from an unforeseeable error
- Sensitivity settings incorrect
- There is an incorrect connection between the cables
- There is no synchronization between the blinking camera and the base station
- The SD card in the car is faulty
How To Fix When My Blink Camera Not Detecting Motion?
This guide has a number of solutions if you continue to encounter this problem over and over again. You should be able to get your Blink camera working again after reading this article.
1. Validate All The Cable Connections
You can check your power connection to see if that is the cause of your Blink Camera Not Detecting Motion issues. You may not be able to connect the power adapter to the wall outlet because it is not connected.
There may be a loose cable or need to replace one with another. Make sure all of the information is correct.
2. Check for Blink Motion Detection
Motion detection could also be a reason why your Blink camera is not recording. You may not have enabled the Blink Camera yet if it’s connected but not working.
The following steps will enable motion detection, so don’t think too much about it.
- Getting started with Blink Camera Not Detecting Motion requires opening the app.
- Choose camera settings from the drop-down menu.
- “Motion detection” will be available to you. Turn it on if you can.
- You must arm your system immediately upon enabling motion detection.
- There may be a delay in the recording when your system starts again.
Also Read: Blink Camera Login
If you are not at home, you would only need to arm your security system. After the system has been fully armed, you only need to allow notifications to be sent to you:
- “Settings” can be found by opening the “settings” app.
- A notification centre or notifications and status bar can be chosen.
- The option to select is “Blink.”.
- Depending on your needs, enable Show notifications.
If your Blink Camera still does not detect motion, make sure the issue has been resolved.
3. An Unknown Error Is Lurking
An unknown error may be residing in your system if you have enabled motion detection and armed your system. The following steps may help you in this case:
- Make sure you sign out of your Blink app before signing back in.
- Once you have restarted your smartphone, you can use it again.
- Make sure the DND mode is turned off. DND mode is easily accessible from the settings.
- Update your Blink application from the play store or app store.
- Then uninstall the app and reinstall it again if the motion detector still isn’t working on your Blink Camera.
Even if you uninstall Blink Camera Not Detecting Motion Sensor, try these steps.
- In the app, navigate to “battery.”.
- The battery-saving mode can be disabled under the “power” option.
- Choose “apps” again under the battery option.
- You can blink apps by clicking on “Blink apps”.
- The battery saver setting should be changed to “No Restrictions”.
4. Check The Sensitivity Settings
In most cases, Blink Camera Not Detecting Motion if the sensitivity setting is too low, but this is not always the case. The moving heat is therefore not detected properly by your system.
If the default settings are not working or someone changed them by mistake, this occurs.
You can correct the sensitivity setting of the Blink camera by following the steps below:
- Open the “camera settings” option from the Blink camera app on your smartphone.
- Find the “sensitivity” slider under the “motion detection” section.
- A slider lets you choose between low and high settings.
- Remember to save your settings after you tap “save”.
Even your pet may be able to trigger the alarm if the sensitivity is set too high. The CCTV camera cannot detect even a single adult if you set the setting to low.
You will not receive an alert notification if you keep changing the sensitivity setting.
It is therefore necessary to set the settings properly in order to resolve the issue of Blink Camera Not Detecting Motion .
Not detecting motion with the Blink Camera is a very irritating issue. This guide covers everything you need to know about how to fix a Blink that is not detecting motion.